Author: Dieter

Gibson style guitars usually have two humbucking pickups, a tone and a volume potentiometer for each humbucker and a toggle switch to select the pickup. How exactly are these components wired together and how do the pot settings affect your sound? In this little article I will give you an answer to these questions and tell you some advantages and disadvantages of this wiring scheme. I will also show you the frequency response of the different settings.

Wiring Scheme

In the diagram you can see that each pickup has independent tone and volume controls. The obvious advantage of this wiring scheme is that you can set two independent sounds and easily switch between them via the toggle switch.

Example Settings:

• Classic Rock
  Neck pickup: Volume 100%, Tone 0% (creamy lead sound)
  Bridge pickup: Volume 70%, Tone 100% (crunchy rhythm sound)
  This is a typical classic rock guitar setting where you can switch between lead and rhythm sound.
• Kill Switch
  Neck pickup: Volume 0%, Tone 100% (short circuit – no output)
  Bridge pickup: Volume 100%, Tone 100% (high output lead or rhythm sound)
  This setting can be used as a special effect instead of a kill switch: Quickly move the toggle switch up and down to create a tremolo-like effect.

One disadvantage of independent volume control is that the mix position of the toggle switch is only useful, if you match the volume settings of both pickups. If you don‘t, one pickup outweighs the other and you can‘t hear much of a difference to the single pickup sound.

Another disadvantage of passive volume control in general is that at lower volume settings the output impedance is very high -> Your signal is more sensitive to electromagnetic disturbances and gets noisier. You don’t have this problem with active guitar pickups.

Frequency Response

I simulated the frequency response of different settings with LTspice XVII. The signal source I used has a flat frequency response and a 10k output resistance.

Conclusions:

• The tone control is an adjustable lowpass filter
• The tone setting does not change at different volume settings (the cut-off frequency stays the same)
• Significant tone change only happens between 0%-10% of the tone pot value -> I recommend using audio taper potentiometers to compensate this unlinearity

I hope this article is useful to you. Please check out the products on this website: My company Songbird FX is a manufacturer of high-quality micro-USB rechargeable guitar pedals.

Selecting the right operational amplifier (short: op amp) for your DIY-project can be a hard task. The variety of op amps is comparable to the number of stars in the sky and the number of specifications in the datasheet is sometimes overwhelming, so how do you choose the right op amp for a specific project? In the following I want to give you an overview of the most important datasheet specifications that you should look after. This little guide is addressed to electronics beginners who want to dive a bit deeper into the topic of operational amplifiers.

What Is An Operational Amplifier?

An operational amplifier is basically a differential amplifier with a very high amplification (ideally infinite). It has a non-inverting and an inverting input, an output and of course pins for the power supply. By using feedback from the output to one of the inputs you can realize many different circuits, for example inverting and non-inverting amplifiers (with finite amplification), integrators, differentiators, low-pass and high-pass filters and many more. For further reading on the different circuits check out Texas Instruments’ “AN-20 An Application Guide For Op Amps”.

The Most Important Datasheet Specifications:

1. Supply Voltage

The one most important spec you should check in the datasheet is the Supply Voltage Range. You find it at Recommended Operating Conditions. If your Supply Voltage is too low your op amp won’t work properly, if it is too high you may even destroy it.

2. Input Common Mode Voltage Range

This specification is sometimes overlooked. The Input Common Mode Voltage Range defines the allowed voltage range of your inputs without malfunction of the op amp. Op amps with rail to rail inputs have an Input Common Mode Voltage Range of V- < Vin < V+, others may include only the positive or the negative rail or neither.

Example:
The typical Input Common Mode Voltage Range of the TL072 includes the positive rail and needs 3 volts of margin to the negative rail:
V- + 3V < Vin < V+                  →           at 10V supply voltage your input voltage range is 3V to 9V

In the Recommended Operating Conditions TI adds a big safety margin:
V- + 4V < Vin < V+ – 4V         →           at 10V supply voltage your input voltage range is only 4V to 6V.

If you want to design your circuit properly you have to use the voltage range stated in the Recommended Operating Conditions (minimum values), however, if you are developing an individual item you can get by with using the typical values by screening the op amps.

3. Input Impedance

The Input Impedance of op amps is of special interest when the signal source impedance is high, for example when using passive guitar pickups. If so, you may want to choose an op amp with JFET-inputs (Input Impedance goes up to 1000GΩ). Op amps with bipolar inputs typically have Input Impedances of about 10MΩ.

4. Equivalent Input Noise and Typical Harmonic Distortion

Op amps do not only amplify your source signal, they also add harmonics and noise. The Equivalent Input Noise and Typical Harmonic Distortion are either stated separately or mixed together as THD+N.
For audio applications it is essential to choose an op amp with low noise and distortion.

5. Supply Current

If your device runs on batteries it is important to keep an eye on the Supply Current. The Supply Current or Quiescent Current provides information on the energy consumption of the op amp without load.
Unfortunately the rule applies that low supply currents result in high noise. You see, choosing the right component is always a trade-off – welcome to electronics 😉

6. Output Impedance

The Output Impedance is important if the load impedance is low, for example if you want to drive headphones or an LED. The Output Impedance has to be much lower than the load impedance, otherwise there would be a big voltage drop on the output (voltage divider between Output Impedance and load impedance). If you don’t find the Output Impedance in your datasheet the Output Source Current gives you similar information.

For detailed information on the above stated specifications and more I recommend you to read TI’s “Understanding Operational Amplifier Specifications“.

How Do I Find The Right Op Amp?

I personally like to use the website of Texas Instruments, because I can type in the specifications that are important to me and the website then shows me suitable op amps including an approximate price. If you want to include other manufacturers too, a great way to do this is using the search function of a big distributor, e.g. Mouser.

I hope this little guide is useful to you. If you are a guitar player, please check out the products on this website: My company Songbird FX is a manufacturer of high quality micro-USB rechargeable guitar pedals.